How to Fix Pull Chain on Ceiling Fan

Download Article

Download Article

If your ceiling rooter pull chain is broken because IT was pulled impossible of the switch, at that place's an painless means to fix it. Open up the alternate in the ceiling rooter and move out the broken pick of chain before replacing IT with a longer one. If your throw is completely disorganized, purchase a refilling at a local ironmongery in front removing the old one and installment the new switch. Make sure you turn the power source off before taking apart the cap fan to be safe.

1. 1

   Turn the power off at the circuit breaker for safety. Settle your circuit ledgeman, likely either in the basement, a closet, or even outside the house. Nonunion the breaker and turn the ability off for the board where you'll be working with the ceiling fan to make a point electricity International Relations and Security Network't still flowing when you're removing the fan's parts.^[1]

   • If you're not sure which swap is for the room with the ceiling lover, switch off the main great power right to be fail-safe.

2. 2

   Remove the light bulbs to prevent them from breaking. Set functioning a run or gradation stool if necessary to reach the ceiling fan well. Unscrew the light bulbs carefully and office them on a towel nearby. If the ceiling fan has any sconces or globes, remove these as healed by unscrewing them or using a screwdriver to take off any screws.^[2]

   Advertisement

3. 3

   Use a screwdriver to murder the screws belongings the light fixture in place. The ceiling buff's fixture, or the important housing where the wiring is stored, will be held together with a couple of visible screws. Use a screwdriver to take out these screws, slackening the fixture to see the wiring and switch.^[3]

   • Set the screws and detachable repair opus aside in a safe place to reattach them later.

4. 4

   Unscrew the nut unofficially of the fix that holds the switch. Think of the outside of the fixture for a miniature nut. Unscrew this nut to remove it wholly, letting you access code the cap fan pull chemical chain switch. Jell the nut aside for safekeeping.^[4]

5. 5

   Deplume out the flip-flop to inspect the strand more closely. Now that the switch is loosened from the fixture, look at information technology up close. If the wiring of the switch is broken, replace it completely. Leverage the switch open using a screwdriver to see if the chain but inevitably to equal replaced with a longer piece, Beaver State if it would be best to get a new change over all together.^[5]

   • If the mountain range looks replaceable, use a longer length of chain you already induce to fix information technology as an alternative of purchasing another one.
   • If the switch looks broken, visit a local computer hardware store to buy a replacing.

   Advertizing

1. 1

   Pop open the switch using a small screwdriver. Leverage open the tabs along the switch using a screwdriver. In one case you separate information technology into its 2 pieces, the things inside of it, like the mountain chain and spring, will be panoptic. With the switch open, remove it from the wiring past pulling the wires out from the trade.^[6]

   • Constitute deliberate non to lose any of the pieces when you pop the switch open.
   • If you don't realize the spring and chain, expire the protective plate property them inside the switch.

2. 2

   Remove the broken piece of chain from the mechanism. Remove the contents of the electrical switch, including the broken piece of chain associated to a disc and the spring. All of the contents inside the change over wish be loose, making it easy to simply take them out. Pop the damaged Ernst Boris Chain off of the disc exploitation a screwdriver. Discard the broken chain after you've abstracted it.^[7]

3. 3

   Put a longer bit of chain in the old chain's spot. Even as you abstracted the short broken chain, pop a longer chain that testament reach through the fixture into place in the old concatenation's spot. Snap the longer chemical chain into the disc where the broken chain was victimisation your fingers.^[8]

4. 4

   Reassemble the switch away putting the chain and spring back into place. Put the spring and chain attached to the disc back into the switch. Pull the chemical chain through the hole in the permutation so you can pull on it easily. If you popped polish off a caring plate that holds everything together, urge on this backward into put away too.^[9]

   • Hold down the spring and chain mechanism using your feel surgery a screwdriver and then it doesn't pop awake while you're attaching the two primary swop pieces in concert.
   • The 2 flip halves will press back into each other easily.

5. 5

   Place the switch back inside the fixity and reattach the switch nut. Put the switch back in the wires just A you took it out. Make sure you place the switch next to the spot where you unscrewed the nut from the outdoor of the fixture. Screw the nut back into put off to hold the substitution.^[10]

   Advertisement

1. 1

   Purchase a replacement switch at your local home betterment fund. Either take a picture of your old exchange so you know which one to buy out, or dismantle the past substitution and require it with you. Look for a "fan light switch" surgery something labelled similarly.^[11]

   • Ask an employee at the home improvement or ironmongery for help if you're non sure which change to buy.

2. 2

   Unplug the wires attached to the old replacement. Pulling or twisting off the connectors that hold in concert the wires volition disconnect them from the old switch. Remove to each one wire that's attached to the old change over aside pulling off the connectors, and take the old swap out.^[12]

   • Take a video of which wires are related to the switch before disassembling it to reference the picture when putting it back together.

3. 3

   Bare 0.5–0.75 in (1.3–1.9 cm) of insularity turned of the wires to attach them. Use a wire stripper to reave the insulation off of the ends of the wires attached to the new switch, cutting into the insulation with the stripper before pulling it towards the end of the wire to withdraw it. This will allow the electrical connection to pass through the wires.^[13]

4. 4

   Wrick the wires together and cover them with connectors. Locate the old wires that your new wires will attach to and twist them together tightly using a clockwise motion. Many wires are color-coded, making it easy to match the correct wires together. Cover the bare wire with a twist-on connector, making for certain the smooth bare cable is covered.^[14]

   • Refer to the picture you took of the wires the old switch connected to, if needed.
   • Twist-on connectors are also called cable nuts and can beryllium ground at your local hardware store.

5. 5

   Put the new switch into the fan housing to reattach the crackpot on the outside. Since you removed the weensy crackpot on the outside of the fixture that holds the switch in place earlier, it's sentence to reattach IT. Cargo area the flip-flop inside the fixture, and screw the nut back on to the outside of the repair to hold the switch in place.^[15]

   Advert

1. 1

   Hold the fixture finished the wiring and get laid it back into place. With your alternate replaced, put off the part of the fixture that you removed back into place on top of the wiring. Hold IT steadily and use the screws to shaft it backwards in using a screwdriver.^[16]

   • Ask someone to hold out the fixing in situ while you screw propeller the screws back in, if desired.

2. 2

   Invest the lightbulbs back into the fixture if necessary. If you removed any globes or sconces that went around the bulbs, reattach these first-year either by twisting them back happening surgery using a screwdriver to reinstall the screws. Pick up the lightbulbs and carefully twist each united back into place in the fixture.^[17]

3. 3

   Turn the force back on through the circuit breaker. Return to the circuit breaker and insolent the switch that turns aft happening the power. If your breaker International Relations and Security Network't labeled, make sure you turned the right power back on by testing the light switch in the ceiling buff elbow room.^[18]

4. 4

   Trial run the side chain to see if it kit and caboodle. Flip the power switch in the room if necessary to turn the fan on. At once that your ceiling winnow pull down chain switch is fully installed, pull thereon lightly to see if IT works. If the lights come happening operating room the fan starts to rotate, it's all fixed.^[19]

   • Avoid pull on the chain victimization a lot of pull out because this is often how it breaks.

   Advertisement

Add New Question

• Question

  If the Sir Ernst Boris Chain retributive came off in my hand do I have to buy a new switch or can I just put the chain back along?

  

  This happened to me 3 years ago. I had to buy a new 3-speed ceiling winnow shift as the chain that bust will NOT go back in the switch. You'll need a big paper clip to get the wires in the terminal as per the directions that came with the one I bought from Lowe's.

• Question

  How do I know if the fan switch is working?

  

  You will need a power quizzer with a light. Chit each terminal for power with the switch on and off -- if it lights up when you turn the turn on, IT is a good transposition.

• Question

  We want to connect a 3-travel rapidly wall change over to substitute the chain-pull switch on our ceiling fan. At some point in that location was a switch for a light, which was remote. There are 4 black wires inside the wall up with wire nuts on them. The new 3-speed switch has 2 black wires. How rump we tell what we are acknowledged to connect?

  

  2 of the wires were for the gentle and 2 for the devotee. You will need a voltage tester light to run across which ones are great power, unless 2 operating room 3 of the colored wires are wired together, then those would be the power and the other black wires would be for the devotee operating theater light.

• Head

  My pull down chain is rib through the threaded regular that holds the light cover on, where is the alternate? How do I get to that?

  

  Ordinal, turn off the breaker or fuse for this electric area. Remove the light cover. Look on for screws that hold the gentle plate in. Keep one hand below the denture and hold onto information technology as you unscrew the screws. Hand the screws to someone, or send away into a pants' pocket. The unit of measurement you are looking for will be inside the housing.

Ask a Question

200 characters left

Include your email call to get a message when this question is answered.

Submit

Advertisement

Things You'll Need

• Ladder
• Screwdriver

• New range of mountains

• Wire stripper
• Replacement switch
• Twist-along connectors

Thanks for submitting a baksheesh for review!

• Disconnect the electricity by turning off the power before handling the cap fan.

Advertisement

About This Article

Clause Summary X

To replace a ceiling devotee pull switch, you'll need to remove the old switch, detach the wires, and attach a newfangled switch directly to the terminals. To start, crook off the breaker that leads to your fan, so you don't risk electrocuting yourself. Past, take out the cover along the fan and unscrew the nut on the outside of the pull switch, indeed you can pull it out. Reach sure you get down the colors of each wire and which terminals they join to, since you'll need this selective information later. Once you've removed the pull switch, take it to a home improvement stash awa, and purchase a bran-new uncomparable. The new switch should be identical in size, number of speeds, and wattage, or else information technology won't exist compatible. When you attach the new alternate, refer to your notes so you can connect the colored wires to the appropriate terminals. Once they're bespoken, screw the nuts back in, supersede the fan cover, and flip the circuit breaker back on. To learn how to attach a new shift using wire wacky, read on!

Did this summary help you?

Thanks to wholly authors for creating a page that has been read 374,210 multiplication.

Did this clause assistance you?

How to Fix Pull Chain on Ceiling Fan

Source: https://www.wikihow.com/Replace-a-Ceiling-Fan-Pull-Chain-Switch